Looking for Answers about How To?

Rubbermaid ships to the 48 contiguous states. We do not ship to P.O. Boxes, APO or FPO addresses or outside of the United States.

"We suggest the following procedure for cleaning your sinkware:
 
Place the sinkware in the sink and cover it with warm water. Add one tablespoon of liquid chlorine bleach per cup of water. Allow the sinkware to soak over night. Remove and rinse thoroughly.
 
We do not recommend the use of powdered cleansers or abrasive pads on the sinkware because these items would scuff the surfaces and allow stains to penetrate even deeper. If you follow one of the above-described cleaning methods on a regular basis, your sinkware should remain fresh and clean and staining will be minimized."

"Use and Care instructions may be obtained from any page by selecting ""Support Center"" at the bottom of the page. Click on ""Use and Care."" Click on the product to download and print the instructions.
 
Use and Care information may also be obtained when viewing the actual photo of the product by selecting the ""Description"" tab and looking under ""Related Links."" Not all products offer this information."

"As our Use and Care brochure states, we recommend avoiding re-heating or placing hot foods high in tomato content in the containers as either action may cause permanent staining. To remove stains, we suggest soaking the stained pieces in a solution of one-tablespoon liquid chlorine bleach per cup of warm water for about 30 minutes. Alternatively, we suggest covering the stain with liquid Palmolive Automatic Dishwasher detergent, allowing it to stand for 30 minutes and then thoroughly rinsing the piece.
We do not recommend the use of any abrasive cleaning pads or cleansers because they would scuff the surfaces and allow stains to penetrate even deeper."

"Rubbermaid identifies most of its products with a recycling symbol molded into the plastic. Be sure to check with your local municipality for items that they recycle. Also, we suggest that you look for information about plastic products on the Internet at: www.plastics.org. "

"Keep foods and beverages stored in containers and coolers from tasting like a science experiment. Wash them with Baking Soda sprinkled on a clean damp sponge. For even tougher odors, just soak items in a solution of 4 tablespoons Baking Soda solution in 1 quart warm water. "

To install, set the shelf on the brackets, aligning the wires from front to back in the bracket slots. Placing your hands on top of the shelf, push down and back so that the line wires (which run left to right) will insert into the notches on the brackets.

If one of the line wires is not completely lined up, you will need to pull the whole shelf out and reinstall.

Only specific products are available for purchase on our website. This item is usually available at Target stores as well as various grocery and drug stores.

To view retailers that carry each of our products, please click on the "Other shopping options" tab.

Our sheds are not designed to be moved while assembled. We recommend that you disassemble the shed and assemble in the new location. Damage could occur while moving the shed. It is also possible for the shed panels to become disengaged, making the shed unstable during or after moving.

Insert the trash bag down through the center of the liner lock wires, then wrap the edge of the bag over the liner lock wires from the inside toward the outsdie as shown in the photo. Lock the liner lock wires in the down position as shown in the photo. Then it is ready to use.

The Configurations Closet Kits are Do-It-Yourself type kits. We provide instructions for a pre-configured design, however we do show on the packaging of the kits several other designs that you may choose from depending on the size of your closet. All of these designs are easily customizeable to fit your needs.

We offer different installation methods for direct mount hardware and wire shelving. For further assistance on installation please contact Rubbermaid Consumer Services through the contact us portion of our website. You may also call 888-895-2110 to speak to a representative, 8:30 to 5:00 ET, Monday through Friday.

To remove the wall anchors, back clips and brackets you will need to grab the circular head of the drive pin with a pair of pliers, turn one-half turn. Release hold of the drive pin, grab the drive pin again pulling straight toward you. This procedure will deactivate the molly hardware piece and then the item can be easily removed from the wall.

To replace the wheels, secure one wheel onto the axle with the end cap. Thread the axle through the openings on the bottom of the container, then attach the second wheel and end cap. Secure the end caps using a rubber mallet. It may also be helpful to place the can on it's side when doing the above steps.

You may download and print assembly instructions for this item from our website, www.rubbermaid.com.

On the home page, in the lower left hand corner, under “support center”, click on “Assembly Instructions. This page lists a description and the model number of our sheds and cabinets. Scroll down to the appropriate category, and click on the model number of your item to download and print the instructions.

Note: this shed must be assembled in the order indicated in the Instructions.

By insuring that the floor is level and on a solid surface, the walls will click into place along the edge of the floor.

If you find that your panels do not click into place, please contact us at 888-895-2110 Monday through Friday 8:30 am to 5:00 pm ET for more troubleshooting information.

When choosing a location in your yard make sure you choose an area with easy access and one that will provide proper drainage for water to run away from the shed location. The shed must be built on a solid, level surface. A cement patio or treated-wood platform is recommended. You can use 2x4 treated lumber 16" on center for support with 5/8" Plywoor or OSB board on top.

The item that you have mentioned is not manufactured by Rubbermaid Consumer Products. It is manufactured by Rubbermaid Commercial Products.

For information regarding their products, you may call them at 800-347-9800 or you may visit their website at www.rcpworksmarter.com.

We do not manufacture replacement handles for the step stool tool box.

To install the anchor, mark and drill a 3/8" hole in the location you are using the anchor. Hammer the wall anchor flush to the wall in the drilled hole. Insert the anchor key to engage the anchor.